CrossFit Home Gym: How to Hang Gymnastic Rings part II

In my first post about hanging rings, I showed you how I put up my personal set of rings in my garage. Over the holiday break, Ditty and I traveled to her parents house and I had another opportunity to hang rings. This time it was for my father-in-law, E, who had gotten us into CrossFit in the first place. (Two years ago he competed in the Masters Division at the South Central Regional CrossFit Games) He had a pair of gymnastic rings hanging outdoors on a pull up bar, but my new brother-in-law and I had the idea of putting them in the garage. Since the setup is different than mine (and probably more like many of you out there) I thought I'd share pictures and descriptions of what we did. 

 To give you an idea of the setup, we were working with a two car garage with 15ft. high ceilings. E wanted the rings pretty much in the middle of the garage so that he would face perpendicular to the garage doors. Luckily, there was a crawl space/small attic above the garage attached to one of the bedrooms.

 One of the biggest tasks was just getting the plywood up off the joists. The claw hammers we had did not grab the wood at the right angle, so it made for a time consuming task of pulling nails up. Eventually we drilled holes large enough at one end to pull the plank of wood up. (see above: there is a square cutout of the plank on the right side)

 After pulling the plank up, we used a tow webbing that was about 25ft. long and draped it across two joists. They acted as both supports so the load was spread out over two joists and also as extensions for the rings to hang from. We then used a drywall saw to cut holes for the webbing to drop down into the garage. Then we drilled holes in the joists and posted U-bolts to keep the webbing from swaying along the joists.

 In order to get the right length of the very long webbing, E was downstairs and attached the rings. We pulled up the slack until he thought they were a good height and then we tied it off using an alpine butterfly knot. (you can probably use any knot that won't loosen, but we just happen to run across this one as we were Googling) After we were finished, we nailed the plank back into place to further hold the webbing and knot in place. (You can also see the back of the U-bolt on the left joist)

 Here is a view from below. As you can see, the webbing made for a very convenient extension and already had extremely strong loops sewn into the ends. All we had to do was connect carabiners!

 Rings at push up level. (Jealous of that rower in the background? me too)

 A view to the outside of the garage.

E on ring push ups. Getting it done.

The next day we did a WOD Fight Gone Bad style (5 stations, 3 rounds of 1 minute of work at each with 1 minute of rest in between rounds)

Wall ball

ring push ups

sit ups

kettlebell swings

Prowler push

After doing a number of ring push ups (and handstand ring push ups) I can personally attest to the stability of the ring setup. If you have a similar setup in your home, go spend a few dollars on webbing and carabiners and get it done!

CrossFit Home Gym: How to Hang Gymnastic Rings

In looking for a new house, one of the big criterion I was looking for was space for a home gym. Although I am a trainer at CrossFit KoP, there are days where it would just be easier to bang out a workout at home. Now that we have a great home with a spacious 1-car garage, my goal is to create a home gym with the ability to park the wife's car in the garage. 


The first thing I had to do was paint the garage. It came with the house unpainted, so I just got some Behr exterior semi-gloss white and got to work. It took just about 2.5 gallon cans to cover the whole garage (19'x10'x11'). 

a close up of one of the supports (resting on Rogue bumpers)

I had already bought a number of Rogue things: a Rogue barbell, Bella barbell, bumper plates, clips, and the rings. The rings offer more versatility than a pull up bar, so my priority was to get the rings up first. Researching different methods from people on the CrossFit forums revealed numerous options. (I tend to do a LOT of research). The best combination for me was to brace the rings through 2x8 pieces of wood that were lag bolted into the ceiling studs (joists). This method allowed me to distribute the load across multiple beams, making it safe and stable.  See the video below to check out the full setup. 

updated 1/3/12 - general list of tools and hardware

TOOLS
stud finder (get one that finds the center of the stud, it will save you time - you get what you pay for, mine was $45 but way better than the $10 one I had originally)
drill and drill bits (standard set includes a variety of diameters)
socket wrench for lag screws
saw (if cutting the wood for your needs)

HARDWARE/supplies
2x6 piece of wood. I got an 8ft. length and cut it to size
lag screws/bolts - these grip the wood extremely well - you'll need 4 - 8 of these, depending on how many ceiling joists you have . Mine were 5/16ths of an inch in diameter and I used 8 total. They were 3.5" long
eye bolts - these are the circular things that hold the carabiners to the wood. 2 total and 3/8ths inch in diameter. Off the top of my head I forget how long, but just enough to go through the 2x8, so maybe 3 total inches including the eye
washers and nuts - get the same size as your eye bolts (mine were 3/8ths of an inch in diameter). these will distribute the load across the wood better. Use washers on your lag screws too. good idea is to get regular washers as well as "lock washers"
2 carabiners

something that you don't absolutely need but I did is to countersink holes in the wood so the nut and washer on top of the eye bolt was "in" the wood. For this you need special drill bits. Mine are "Ryobi forstner bits" from home depot.

there are a lot of great discussions on the CF forum, (mainpage) so check it out and do some searching around. Google is your friend!

For those with a crawl space above your garage, here is a solution for that setup:

CrossFit Home Gym: How to Hang Gymnastic Rings part II